TOOLS

The Lifter Bleeder Tool is designed to pre bleed and remove all air from lifter bearings and hydraulic units. Simply load lifters in basket, set in...

OHLINS CARTRIDGE KIT INSTALLATION TOOLS Specialty tools used to install Ohlins Nix / FKS series cartridge kits Please refer to your installation m...

INTAKE MANIFOLD WRENCH Special bends make it easy to reach those tricky intake manifold bolts 1/4" allen on one side, the other is a 1/4" ball all...

Transmission Sprocket Locking Tool for Chain Drive, locks the main drive gear and sprocket and allows proper torquing and removal of nut without ha...

TRANS PULLEY LOCKING TOOL (FOR BELT DRIVEN REAR WHEELS) Holds the transmission pulley in place for removal or install Excellent tool if you do not...

MINI BRAKE BLEEDER WITH CHECK VALVE Combines wrench and bleeder valve into one convenient and compact tool Fits most 8mm & 10mm bleeder nipple...

STARTER JACK SHAFT HOLDING TOOL You no longer have to destroy a screw driver or jam a rag in the starter teeth! Slides over the starter teeth, all...

Stock FXR axle adjusters are small eyelets welded to a stud. Due to the small surface area, your swing arm can dent or "mushroom" in. After the swi...

CLYMER REPAIR MANUALS Whether it's simple maintenance or complete restoration, don't start work without Clymer, the leader in service manuals Save...

The Primary Alignment Tool is designed to simplify getting your engine sprocket, clutch basket and primary chain all in perfect alignment when chan...

CLUTCH ADJUSTER NUT TOOL For use on all '85 and later Big Twin Harley-Davidson models with an 11/16" clutch adjuster lock nut (Excluding applicati...

RATCHETING LOW PROFILE ROCKER BOX WRENCH (EVO & SPORTSTER) Low profile to allow clearance between frame and engine Works great on '84-'99 Evol...

The adjustable Magnetic Lifter Holder Set for Harley-Davidson Evolution, Twin Cam, and M8 motors is the best Lifter Holder available. Adjustable he...

REDA FUEL CAN Designed for Harley touring bags however it fits most other saddlebags as well! (Works great in Leather Pros bags!) Excellent back u...

RATIO RITE MEASURING CUP For measuring all sorts of chemicals! Measures cubic centimeters, ounces and pints Eliminate the mistakes and guesswork o...

REAR WHEEL ALIGNMENT TOOLS Designed to help set rear wheel alignment Fast, accurate and easy to use Eliminates the need to use a tape measure Corr...

Innovative design makes tool easier and safer to use than old fashioned pin aligned drivers Anodized aluminum locking ring features knurled finish...

FUEL TANK LOCK RING TOOL ('08+ TOURING) Remove and install the lock ring on fuel tank located under the dash Allows access to the fuel filter and ...

LEXIN PRODUCTS ARE TEMPORARILY UNAVAILABLE PLEASE SEE ALL OF OUR OTHER COMMUNICATION OPTIONS HERE: AUDIO AND COMMUNICATIONS The New P5 Advanced Sma...

STEERING BEARING RACE TOOL 2-In-1 Design quickly and precisely removes and installs outer bearing race from the steering head without the use of a...

SUPER SLIM ROCKER BOX WRENCH (EVO & SPORTSTERS) Designed to reach hard-to-get-at 3/16" hex screw on the rocker boxes of '84-'99 Evolution big ...

This tool is used to move the ignition switch from one position to another when the knob is removed. It can also be used to align the internal lug...

PRO FORK OIL LEVEL TOOL Use this tool to accurately check and adjust the oil level on conventional and cartridge forks Adjustable ring will measur...

TRANS PULLEY NUT SOCKET Tool is a heavy duty thick wall tube, extra long. Tool has a 2 piece design, a centering inner collar will thread onto th...

EXHAUST STUD DRILL PLATE FIXTURE Used to drill out broken off exhaust studs Drill plate keeps the drill bit centered Includes drill bit Most studs...

Used to lock the primary drive to allow you to remove the compensator nut/bolt and/or the clutch hub nut. Works on all models! Made of very stiff ...

PBR CHAIN TOOL (ALL IN ONE) The easiest and our personal favorite chain tool! Innovative design will Press, Break & Rivet 520, 525, & 530 ...

Replacing the clutch on your H-D® is a lot easier and faster with the Motion Pro Clutch Spring Compression Tool Strong die cast steel frame with h...

Quit using shop towels to cover up case bore openings. Foreign material that gets into your bottom end can cause major damage, using a shop rag can...

PUSHROD TUBE HOLDER Makes for easy adjustment of adjustable pushrods, holding pushrod tubes up and out of the way Fits M8, Twin cam, Evolution big...

CLEAR TIMING HOLE PLUG Plastic plug locates the timing mark without getting an eye full of oil Fits Big twin & Sportsters with a left side cra...

V2 OIL FILTER STRAP WRENCH For use on stuck or stubborn oil filters! Fits all spin-on type oil filters (Motorcycles, cars, etc!) For use with 3/8"...

SWIVEL 36MM AXLE SOCKET Facilitates loosening and tightening of hard to reach rear axle nut on HD baggers Works great to get around bag rails and ...

STEERING STEM BEARING TOOL Removes and installs tapered roller bearing OEM #48300-60 at base of the lower steering stem (Triple tree) Fits most H...

SPARK PLUG GAP TOOL Spark plug tool measures spark plug gap in graduated ramp sequence Sizes: SAE .020" - .100"; Metric .60 mm - 2.40 mm Universal...

FUEL CHECK VALVE REBUILD TOOL Provides for fast and easy professional installation of check valve O-ring or Rebuild kit without having to remove t...

Correct style driver/socket for the compensating sprocket retaining fastener Made in the U.S.A. For compensator #36500034A found on 14'+ Touring, ...

PRIMARY LOCKING TOOL Used to lock the primary drive on Big twins and Sportsters Universal application works on all models Made in the USA

RATCHETING CRANK SHAFT ROTATOR WRENCH Use to rotate the crankshaft during engine timing and clearance checks EZ Grip screwdriver-style handle for ...

CRANKSHAFT RUN OUT TOOL Mounts to cam chest side of engine case using designated mounting holes of tool combined with cam-cover bolt holes Makes f...

39 & 49MM FORK CAP SOCKET Use for removal and installation of the fork cap nut (1 3/8" hex) Fits Big Twin and Sportster models with 39 & 4...

Standard oil filter wrench : 14-flute socket with a cutout design to clear crank sensor Fits Drag Specialties, Harley & most other branded fil...

HEX AXLE SOCKET TOOL Fits internal axle hex on '18+ model Softails and many other dirt/sport bikes! Four metric hex sizes: 17, 19, 22 and 24mm 3/8...

ULTIMATE CLUTCH ADJUSTING TOOL Allows the quick and accurate tightening of the clutch adjusting screw jam nut without having the screw change posi...

TAPPET/LIFTER BLOCK ALIGNMENT SCREW Used when installing tappet/lifter blocks to ensure all oil passages and gaskets are perfectly aligned. Fits 7...

BELT TENSION GAUGE A super crucial step to prolong belt and pulley life! A must have when installer taller or shorter suspension! Compact design S...

RATCHETING 36MM AXLE WRENCH Reversible ratcheting wrench used to install and remove 36 mm axle nuts Low profile wheel allows access to the nut wit...

RATCHETING INTAKE MANIFOLD WRENCH Features a reversible action and an 1/4" ball-end Allen bit end for flexibility in tight areas To install and re...